DiabloFormulaRacing 180views. Before messing with anything always, ALWAYS disconnect the battery. Step one: Chalk the front tires and jack up the rear of the car. Put car in Neutral (Apprx time 3-5min) 2. Take off the bolts holding the.
Specifically I need how to unbolt the flywheel and remove the transfer case. Flush the transmission oil cooler and lines, if necessary. Connect the transmission oil cooler lines to the transmission. Total time is probably about 6-hours for a first timer that is mechanically skilled. Step By Step Instructions For Replacing The 4L80E in Your Suburban.
TRANSMISSION DISASSEMBLY Place the transmission on a sturdy workbench. Remove the transmission mounting bell housing. This is not a task for a bargain tool.
The Torx fasteners used to assemble the bell to the trans have a T-recess, and are not only torqued to a high level but have had adhesive applied. Oil cooler lines from the transmission. Plug all openings in the transmission and the oil cooler lines. L30E 4L60E 4L80E 4T40E Transmission Harness Connector Removal Tool, All TECKPAK FITZALL Products Available On Line,.
GM 4LE Transmission Pump Tool. The sixth-generation Chevrolet Corvette was also equipped with the 4L60E transmission. L60E Transmission Front Pump Seal Reainer. If you are able to remove and reinstall your 4L60E transmission , but do not want to take on the job of rebuilding it, you have come to the right place.
I only offer the transmission rebuild service. No transmission removal or installation service is offered. Buying a used 4L60E transmission may save you money. However, if the unit does not work properly after installe you will more than likely have to pay the labor again for removal and reinstall of the transmission PLUS the freight to ship the transmission back to the salvage yard. I recieved my 4l60e valve body a few weeks ago.
The part was very well packaged. Great product, I would recommend Ken Partin Transmission parts to anyone and will. Though most automatic transmission diagnoses and repairs are beyond the scope of the home mechanic, you can diagnose some common issues without specialized tools or training. Entire transmission cooling system must be completely cleane hot flushe and flow tested. If the cooler is plugge it must be replaced.
The 4L60E transmission weighs 1pounds dry, and 1wet. With the fluid draining out slowly remove the last bolt. Now the pan is off next thing is to remove the filter. Fits 4L60E , 4L65E, 4L70E and 4L75E 93-Up Except Hybrid units.
Boost Valve Fits both early long and later model short type Boost Valve assembly.
Arizona Transmission Machine has introduced a 6L80-E pump. Common problems with the 4L60E transmission include the third and fourth gears not working, slow or slipping reverse gear and sudden grinding noise in second gear. Almost every rear-wheel drive vehicle manufactured by General Motors features the 4L60E transmission. Best Answer: the transmission has to come out and then remove the torque converter ! The General Motors 4l60e automatic transmission is a very common transmission used in light and medium duty trucks, passenger cars and sports cars.
Replacing the torque converter in this transmission is simple but it is very common for mechanics to incorrectly install it.
I have obtained the new gear from Advance Adapters. Since it slides on, I have to remove that OEM gear. Tried to twist it to remove it (even with heat) with negative. Learn how and when to remove this template.
It weighs 1pounds without transmission fluid. Installation and Operation Manual for 4L60E , 4L65E, 4L70E, 4L80E, and 4L85E transmissions. US Shift Transmission Control System instruction and operation manual.
The first step will be to remove the cover over bottom of the pins on the 4L60E transmission plug. There is a small plastic tab holding each pin in place, this tab must be lifte then push the pin over, and out the back of the connector. I believe the 3-clutches are melted or just stuck so the input drum will not pull out like it normally would do. How to remove the input housing from a 4l60e transmission ? I have tryed dropping the transmission on the bell housing onto a concrete pad with cardboard on top.
GM Snap Ring Removal Tool. BUT what is the easiest way to remove the existing. Drive the truck and get the transmission up to operating temp. A considerable portion of the cost of a remanufactured transmission install is the labor cost to remove and re-install the transmission (RR). Visit our DIY Center for transmission removal and installation procedures.
Label each pair of wires, so as not to confuse the shift solenoids on the rear of the transmission. The shift solenoids are held in place with aU-clip that must be removed from below in a journal in the valve body. Pop the shift cable from the ball-joint on the shift lever with a flat head screw driver.
Squeeze the two plastic extrudes and push back through the bracket or out the side.
No comments:
Post a Comment
Note: only a member of this blog may post a comment.