Change ignition key

Slide out the ignition switch assembly and unplug the wires from the back of it. Remove the small screw from the back of the ignition assembly. Place a small amount of grease on the end of the new switch.

Plug the wires into the new switch. Reassemble all parts by reversing the steps above. Order a replacement ignition key from a locksmith.

It generally takes a few hours for the locksmith to check your ignition against the key s they have in stock and find the right one, as well as cut down and form the right size and shape of key for your car. Check the new key by inserting it into the ignition. You may need to turn the new ignition key in the lock cylinder to the accessories position before inserting it into the ignition switch.

Test your ignition switch by reconnecting the electrical connections and the negative battery terminal cable.

The ignition switch serves to send power from the battery. When you turn your key to turn on your vehicle, the ignition switch takes power from the battery and sends it to the starter, which allows your vehicle to turn on. We know our parts and products. Wiggle the wheel back and forth while turning the key.

In order to unlock the steering wheel, insert the key into the ignition and attempt to turn it. While applying light pressure to the key , wiggle the steering wheel back and forth until the lock disengages. This will allow the steering wheel and the key to turn. Shopping for ignition switch replacement: An ignition switch can be replaced by a car dealership, an independent repair shop, or car-repair chains like Pep Boys or Sears.

Both the National Institute for Automotive Service Excellence and the International Automotive Technicians Network provide a searchable directory of repair shops. Call them and ask for parts they will know. If you are able to turn the key and nothing happens then you do not need a new cylinder as this is only a mechanical link between the key and the ignition switch. The switch is located on the oposite side of the ignition cylinder on the column and that would be the first place to check for powers to the switch and then check to make sure you have.

Ignition Switch Replacement. Most ignition switches function with the turning of a key while more modern cars have updates to push button style ignitions. Install the column-to-dash trim plate.

With the turn signal lever in neutral and the flasher knob out, slide the thrust washer, upper bearing pre-load spring, and canceling cam onto the shaft. Adjust the ignition switch retained from the housing with the damaged lock cylinder, and install it onto the new lock cylinder housing. If the only thing wrong with it is the key , you will not be able to replace the car with a good one for $180. How to change ignition switch.

Before you begin, you have to get the core key for the switch. Rather than unlocking the car doors and locks, it enables the removal of the cylinder, or core, from the ignition lock casing. The core key is like a master key. Unfasten the ignition switch connector under the instrument panel. Push the lock cylinder stop in with a small, round object (cotter pin, punch, etc.).

Insert key B into ignition switch within seconds. Turn ignition switch to position II. If engine does not start and clock LED flashes: Switch ignition ON.

Is your ignition key difficult to turn, and then, getting stuck on removal from the ignition barrel of your Discovery Series II? Gently remove the ignition switch from the upper triple clamp. Finally, you can replace your old ignition switch with a new set and reverse these steps to re-install the device. For Generator parts and accessories, think Jack’s! If the door key is same as the ignition key , the door tumbler can be removed and a key made if no security chip is installe (older cars).

Weighted Key Chain Step - Most worn key problems will need a key ordered from the dealer using the vehicles VIN number. Reverse the process to install your new ignition switch cylinder. Unscrew the shroud around the steering column with a Phillips head screwdriver.

Pull the shroud out from around the steering column once it is loosened.

Locate the switch by the ignition lock. So I purchased a new set of door locks and ignition key tumbler. No key is required for removal. There are parts to remove and replace to pull the ignition from a Saginaw column and several specialized tools involved. Step 6: Position the new switch in place of the old one.

Release the cylinder by depressing the pin that holds it in place. Turn the switch off and insert the key in the switch. Put the key again to the lock point and then remove the key. The process of changing an ignition can change dramatically from vehicle to vehicle, and the pricing for parts can swing as well. Then you must disengage the old key cylinder from the old switch.

Replace the old switch with the new one and connect the old cylinder with the brand new ignition switch. Restore all the wiring connections as before and put the other switches along with the steering wheel back in place. Press the punch or screwdriver upwards and using your other han remove the complete assy of the ignition cylinder, with the key on it After the old ignition cylinder is remove put the new one in the same position ( LOCK ) and simply slide it in.