How to remove a broken key from a car ignition

If it does not move, then you will have to have it towed to the dealer or call a locksmith who is able to remove the broken key. This is done by tapping the lock cylinder firmly on a block of wood until the broken key piece. Use a pair of needle-nose pliers to pull out the broken tip.

A locksmith has the tools to do the job - about $50. Remove the head of the broken key from the ignition switch. Be careful not to pull your wire out with the key handle.

You want to keep it in place on the broken piece of key still in your ignition. Grip the broken piece of key between the wires. It may help to twist the wires around each other to secure a good grip. If there is enough of the broken key sticking out of the ignition , you can use needle-nose pliers to latch onto the key and pull it out. Turn the wire toward the teeth of the key.

Slowly try to catch a tooth in the bent wire and pull the wire out of the lock with the key. Step 5: Pull the broken key out with pliers. Once a small part of the broken key comes out of the cylinder, use your needle-nose pliers to pull it out completely. Demonstration of how to extract and remove broken Car key stuck in Car Ignition using Stainless steel picture wire.

Go for the edge where you have the best access to the side of the key and work at it. If no side of the key works you can also try the edge of the key , but there you are often looking at a place that is slanted wrong. How to Get a Broken Key Out of a Car Ignition. Spray a little cooking spray or WD-into the ignition and try again with the hacksaw blade.

Remember to try both in front of and behind the key , and to wiggle the blade. Do not spray the lubricant before trying the pliers or wire,. Once the pliers take hol pull out the broken bits. Use the tweezers to remove the remaining pieces.

Insert an orange handle wire on each side of broken key. Twist wires together, and pull out broken key. If key is stuck, insert red handle pliers and spread open tumblers.

When a key breaks off in the lock, most people go right for the tweezers. Your main concerns should be the thickness of your tweezers and how far the broken key is in the lock. Most tweezers are inappropriately sized for this task and will just end up pushing the key farther into the keyway.

Also, grab a pair of needle nose pliers, because even though these methods will remove the broken key , pliers will help to get it out that much faster. Once enough of the key is accessible, you can just pull it free with your pliers. Wiggle the handle end until the blade squeezes in next to the key. If you are trying to remove a car key that has teeth on both sides of the key , you can slide the saw blade in with the teeth up or down.

These require a gentle touch but will usually get it. Slide it in the loosest part, twist gently to get the teeth to grab the key and pull straight out. Grab onto the key shaft by twisting your saw blade a little.

When it gets a grip, try to slide the shaft out of the lock. Apply gentle force when doing this to avoid damaging the key. You can use a small tack hammer to straighten it up. Starting a car by removing the key cylinder is an illegal act if the car is not yours. However, there may come a time when, for whatever reason, you need to do just that.

Perhaps you lost your key , the ignition lock tumbler has faile or the key is broken or bent. There is a little piece of the key sticking out the ignition so I tried to grab it with a plyers and remove the key. The key needs to be turned before it can be remove as the key broke. I went to start my car today, and I could not find my key so I used a spare one.

Make your own animated videos and animated presentations for free. Key is broken inside the ignition switch, how to remove with out calling pop a lock. This car has a key that is broken - Answered by a verified Ford Mechanic We use cookies to give you the best possible experience on our website. Below are the top causes of a key getting stuck in the ignition. Parking Gear Not Set – The gear of the transmission must always be set to park before attempting to remove a car key from the ignition.

If the gear is set to drive, neutral, or any other available gear, then the key will not come out. If your gear position is not in park or neutral, you may not be able to remove the key. Try and shake the shifter to find the ideal lock position and then try removing the key. Reply Re: Key broken off in ignition ! The bad news is that if you lose your smart key and don’t have a spare, you’ll long for the aggravating antiquity of extracting that broken key out of your ignition lock.

Here are four methods to safely and effectively remove a broken key from the cylinder. Luckily, you can usually get the broken pieces out without calling a locksmith. Clear away any obstructions in the ignition lock.

Slide a thin, stiff wire along the sides the broken key. Place the place entire key back into the lock. A broken key extractor works by holding the teeth of the key using its unique hooks. If you happen to access a broken key extractor either from a locksmith or a Good Samaritan, then place the tool inside the keyhole along the rough side of the key. Turn and pull to grab the key and remove.

Having a key get stuck in the ignition switch of a car is not an uncommon problem.